View VNL5160N3-E_7492889.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

february 2012 doc id 16364 rev 2 1/26 1 VNL5160N3-E vnl5160s5-e omnifet iii fully protected low-side driver features drain current:3.5a esd protection overvoltage clamp thermal shutdown current and power limitation very low standby current very low electromagnetic susceptibility in compliance with the 2002/95/ec european directive open drain status output (a) specially intended fo r r10w or 2x r5w automotive signal lamps description the VNL5160N3-E and vnl5160s5-e are monolithic devices, made using stmicroelectronics ? vipower ? te c h n o l o gy, intended for driving resistive or inductive loads with one side connected to the battery. built-in thermal shutdown protects the chip from overtemperature and short circuit. output current limitation protects the devices in an overload condition. in the case of a long duration overload, the device limits the dissipated power to a safe level up to thermal shutdown intervention. thermal shutdown, with au tomatic restart, allows the device to recover normal operation as soon as a fault condition disappears. fast demagnetization of inductive loads is achieved at turn-off. type v clamp r ds(on) i d VNL5160N3-E 41 v 160 m 3.5 a vnl5160s5-e a. valid for vnl5160s5-e only. 1 2 2 3 sot-223 so-8 table 1. device summary package order codes tube tape and reel sot-223 VNL5160N3-E vnl5160n3tr-e so-8 vnl5160s5-e vnl5160s5tr-e www.st.com
contents VNL5160N3-E, vnl5160s5-e 2/26 doc id 16364 rev 2 contents 1 block diagrams and pins confi gurations . . . . . . . . . . . . . . . . . . . . . . . . 5 2 absolute maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.1 absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.2 thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 electrical characteristi cs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4 application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4.1 mcu i/o protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5 package and pc board thermal da ta . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5.1 sot-223 thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5.2 so-8 thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 6 package and packing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 6.1 ecopack ? packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 6.2 sot-223 mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 6.3 so8 mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 6.4 sot-223 packing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 6.5 so8 packing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 7 revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
VNL5160N3-E, vnl5160s5-e list of tables doc id 16364 rev 2 3/26 list of tables table 1. device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 table 2. pin function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 table 3. suggested connections for unused and not connected pins . . . . . . . . . . . . . . . . . . . . . . . . 7 table 4. absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 table 5. thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 table 6. powermos section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 table 7. source drain diode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 table 8. input section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 table 9. status pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 table 10. logic input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 table 11. openload detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 table 12. supply section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 table 13. switching characteristics (vcc=13v). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 table 14. protection and diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 table 15. truth table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 table 16. sot-223 thermal parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 table 17. so-8 thermal parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 table 18. document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
list of figures VNL5160N3-E, vnl5160s5-e 4/26 doc id 16364 rev 2 list of figures figure 1. VNL5160N3-E block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 figure 2. vnl5160s5-e block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 figure 3. VNL5160N3-E current and voltage conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 figure 4. vnl5160s5-e current and voltage conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 figure 5. configuration diagrams (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 figure 6. switching characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 figure 7. VNL5160N3-E application schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 figure 8. vnl5160s5-e application schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 figure 9. maximum demagnetization energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 figure 10. sot-223 pc board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 figure 11. sot-223 rthj-amb vs pcb copper area in open box free air condition . . . . . . . . . . . . . . . 16 figure 12. sot-223 thermal impedance junction ambient single pulse . . . . . . . . . . . . . . . . . . . . . . . 17 figure 13. sot-223 thermal fitting model (1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 figure 14. so-8 pc board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 figure 15. so-8 rthj-amb vs pcb copper area in open box free air condition . . . . . . . . . . . . . . . . . . 19 figure 16. so-8 thermal impedance junction ambient single pulse. . . . . . . . . . . . . . . . . . . . . . . . . . . 19 figure 17. so-8 thermal fitting mode (1) l. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 figure 18. sot-223 mechanical data & package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 figure 19. so8 mechanical data & package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 figure 20. sot-223 tape and reel shipment (suffix ?tr?) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 figure 21. so-8 tube shipment (no suffix) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 figure 22. so-8 tape and reel shipment (suffix ?tr?) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 4
VNL5160N3-E, vnl5160s5-e block di agrams and pins configurations doc id 16364 rev 2 5/26 1 block diagrams and pins configurations figure 1. VNL5160N3-E block diagram figure 2. vnl5160s5-e block diagram $2!). #ontrol$iagnostic ,/')# $2)6%2 #urrent ,imitation 0o wer #lamp /6%24%-0%2!452% 02/4%#4)/. /6%2,/!$02/4%#4)/. !#4)6%0/7%2,)-)4!4)/. ).054 '.$ ("1($'5 $2!). #ontrol$iagnostic ,/')# $2)6%2 #urrent ,imitation 0ower #lamp /&&3tate /penload /6%24%-0%2!452% 02/4%# 4)/. /6%2,/!$02/4%#4)/. !#4)6%0/7%2,)-)4!4)/. ).054 34!453 '.$ 3500,9 3500,9 6/,4!'% ("1($'5
block diagrams and pins confi gurations VNL5160N3-E, vnl5160s5-e 6/26 doc id 16364 rev 2 figure 3. VNL5160N3-E current and voltage conventions figure 4. vnl5160s5-e current and voltage conventions table 2. pin function name function input voltage controlled input pin with hysteres is, cmos compatible . controls output switch state (1) 1. internally connected to v supply in the VNL5160N3-E. drain powermos drain source powermos source and ground reference for the control section supply voltage supply voltage connected to the signal part (5v) status open drain digital diagnostic pin (2) 2. valid for vnl5160s5-e only. drain input source i d i in v in v ds drain input source i d i in v in v ds status supply v stat v supply i stat i s voltage
VNL5160N3-E, vnl5160s5-e block di agrams and pins configurations doc id 16364 rev 2 7/26 figure 5. configuration diagrams (top view) table 3. suggested connections for unused and not connected pins connection/pin status n.c. input floating x x x to ground not allowed x through 10k resistor sot-223 so-8
absolute maximum rating VNL5160N3-E, vnl5160s5-e 8/26 doc id 16364 rev 2 2 absolute maximum rating stressing the device above the rating listed in ta b l e 4 may cause permanent damage to the device. these are stress ratings only and operation of the device at these or any other conditions above those indicated in the operat ing sections of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. refer also to the stmicroe lectronics sure program and other relevant quality document 2.1 absolute maximum ratings table 4. absolute maximum ratings symbol parameter value unit sot-223 so-8 v ds drain-source voltage (v in =0v) internally clamped v i d dc drain current internally limited a - i d reverse dc drain current -4 a i s dc supply current - -1 to 10 ma i in dc input current -1 to 10 ma i stat dc status current - -1 to 10 ma v esd1 electrostatic discharge (r=1.5k ; c=100pf) ?input ?status ? supply ? drain 4000 4000 4000 5000 v v esd2 electrostatic discharge on output pin only (r=330 , c=150pf) 2000 v t j junction operating temperature -40 to 150 c t stg storage temperature -55 to 150 c e as single pulse avalanche energy l=8.5mh, t j = 150 c, r l =0 , v batt =13.5v, i out =i liml 37 mj
VNL5160N3-E, vnl5160s5-e absolute maximum rating doc id 16364 rev 2 9/26 2.2 thermal data table 5. thermal data symbol parameter maximum value unit sot-223 so-8 r thj-amb thermal resistance junction-ambient 146.8 (1) 1. when mounted on a standard single-sided fr4 board with 0.5cm2 of cu (at least 35 m thick) connected to all drain pins 103.1 c/w
electrical characteristics VNL5160N3-E, vnl5160s5-e 10/26 doc id 16364 rev 2 3 electrical characteristics values specified in th is section are for v in =v supply = 4.5 v to 5.5 v, -40 c < t j <150c, unless otherwise stated. table 6. powermos section symbol parameter test conditions min. typ. max. unit v supply operating supply voltage 3.555.5v r on on-state resistance v in =v supply =5v i d = 1 a; t j = 25 c i d = 1 a; t j = 150 c 160 170 320 m m v clamp drain-source clamp voltage v in = 0 v; i d = 1 a 41 46 52 v v clth drain-source clamp threshold voltage v in = 0 v; i d = 2 ma 36 v i dss off-state output current v in = 0 v; v ds = 13 v; t j = 25 c v in = 0 v; v ds = 13 v; t j = 125 c 0 0 3 5 a table 7. source drain diode symbol parameter test conditions min. typ. max. unit v sd forward on voltage i d = 1 a; v in = 0 v 0.8 v table 8. input section (1) 1. valid for VNL5160N3-E option (input & supply pins connected together). symbol parameter test conditions min. typ. max. unit i iss supply current from input pin on-state v in = v supply = 5 v; v ds = 0 v 30 110 a v icl input clamp voltage i s = 1 ma i s = -1 ma 5.5 -0.7 7v v v inth input threshold voltage v ds = v in ; i d = 1 ma 1 3.5 v
VNL5160N3-E, vnl5160s5-e electrical characteristics doc id 16364 rev 2 11/26 table 9. status pin (1) 1. valid for vnl5160s5-e option. symbol parameter test cond itions min. typ. max. unit v stat status low output voltage i stat = 1 ma 0.5 v i lstat status leakage current normal operation, v stat = 5 v 10 a c stat status pin input capacitance normal operation, v stat = 5 v 100 pf v stcl status clamp voltage i stat = 1 ma i stat = -1 ma 5.5 -0.7 7v v table 10. logic input (1) 1. valid for vnl5160s5-e option. symbol parameter test conditions min. typ. max. unit v il input low level voltage 0.9 v i il low level input current v in = 0.9 v 1 a v ih input high level voltage 2.1 v i ih high level input current v in = 2.1 v 10 a v i(hyst) input hysteresis voltage 0.13 v v icl input clamp voltage i in = 1 ma i in = -1 ma 5.5 -0.7 7v v table 11. openload detection (1) 1. valid for vnl5160s5-e option. symbol parameter test conditions min. typ. max. unit v ol open-load off-state voltage detection threshold v in = 0 v 0.6 1.2 1.7 v t d(oloff) delay between input falling edge and status falling edge in openload condition i out = 0 a 45 425 1100 s table 12. supply section (1) 1. valid for vnl5160s5-e option. symbol parameter test cond itions min. typ. max. unit i s supply current off-state t j = 25 c; v in = v drain = 0 v; on-state t j = 25 c; v in = 5 v; v ds = 0 v 10 25 25 110 a a v scl supply clamp voltage i scl = 1ma i scl = -1ma 5.5 -0.7 7v v
electrical characteristics VNL5160N3-E, vnl5160s5-e 12/26 doc id 16364 rev 2 table 13. switching characteristics (vcc=13v (1) ) symbol parameter test conditions sot-223 (2) so-8 unit min. typ. max min. typ. max. t d(on) turn-on delay time r l = 13 , v cc = 13v (3) 8.9 8.9 s t d(off) turn-off delay time r l = 13 , v cc = 13v 13.2 13.2 s t r rise time r l = 13 , v cc = 13v 14.1 14.1 s t f fall time r l = 13 , v cc = 13v 11.5 11.5 s w on switching energy losses at turn-on r l = 13 , v cc = 13v 34.3 34.3 j w off switching energy losses at turn-off r l = 13 , v cc = 13v 34.3 34.3 j 1. see figure 7: VNL5160N3-E application schematic and figure 8: vnl5160s5-e application schematic . 2. 3.5 v < vs upply =vin<5.5v. 3. see figure 6: switching characteristics . table 14. protection and diagnostics symbol parameter t est conditions (1) 1. v supply =v input in VNL5160N3-E version. min. typ. max. unit i limh dc short circuit current v ds = 13v; v in =v supply =5v 3.557.5a i liml short circuit current during thermal cycling v ds = 13v; t r < t j < t tsd; v in =v supply =5v 2.5 t dlim step response current limit v ds = 13v; v input = 5v 20 s t tsd shutdown temperature 150 175 200 c t r reset temperature t rs +1 t rs +5 c t rs (2) 2. valid for vnl5160s5-e option. thermal reset of status 135 c t hyst thermal hysteresis (t tsd - t r ) 7c
VNL5160N3-E, vnl5160s5-e electrical characteristics doc id 16364 rev 2 13/26 figure 6. switching characteristics table 15. truth table (1) 1. valid for vnl5160s5-e option conditions input drain status normal operation l h h l h h current limitation l h h x h h overtemperature l h h h h l undervoltage l h h h x x output voltage < v ol l h l l l h t i d 90% 10% t v gen t d(on) t d(off) t f t r
application information VNL5160N3-E, vnl5160s5-e 14/26 doc id 16364 rev 2 4 application information figure 7. VNL5160N3-E application schematic figure 8. vnl5160s5-e application schematic +5v c r prot input drain v cc r l source
VNL5160N3-E, vnl5160s5-e application information doc id 16364 rev 2 15/26 4.1 mcu i/o protection st suggests to insert a resistor (rprot) in line to prevent the c i/o pins from latching up (b) . the value of these resistors is a compromise between the leakage current of c and the current required by the ls d i/os (input levels compatibility) wi th the latch-up limit of c i/os: 0.7/i latchup r prot (v ohc -v ih ) / i ihmax calculation example: for the following conditions: i latchup 20ma v ohc 4.5v 35 r prot 100k . recommended value is r prot =10k figure 9. maximum demagnetization energy b. in case of negative transient on the drain pin. 0.1 1 10 110100 l (mh) i (a) vnl5160x - single pulse repetitive pulse tjstart=100c repetitive pulse tjstart=125c
package and pc board thermal data VNL5160N3-E, vnl5160s5-e 16/26 doc id 16364 rev 2 5 package and pc board thermal data 5.1 sot-223 thermal data figure 10. sot-223 pc board note: layout condition of r th and z th measurements (pcb fr4 area = 30 mm x 30 mm,pcb thickness = 2 mm, cu thickness=35 m, copper areas: from minimum pad layout to 0.8 cm 2 ). figure 11. sot-223 r thj-amb vs pcb copper area in open box free air condition gapgcft005 3 0 rthj_amb(c/w) rthjamb 60 70 80 90 100 110 120 130 140 150 160 0 0.5 1 1.5 2 2.5 pcb cu heatsink area (cm^2) - (refer to pcb layout) footprint
VNL5160N3-E, vnl5160s5-e package and pc board thermal data doc id 16364 rev 2 17/26 figure 12. sot-223 thermal impeda nce junction ambi ent single pulse equation 1: pulse calculation formula where = t p /t figure 13. sot-223 thermal fitting model (1) 1. the fitting model is a simplified thermal tool and is valid for trans ient evolutions where the embedded protections (power limitation or thermal cycling during ther mal shutdown) are not triggered. table 16. sot-223 thermal parameter area/island (cm 2 )fp2 r1 (c/w) 1.4 r2 (c/w) 1.8 r3 (c/w) 4.5 r4 (c/w) 24 0.1 1 10 100 1000 0.0001 0.001 0.01 0.1 1 10 100 1000 time (s) zth (c/w) footprint 2 cm 2 z th r th z thtp 1 ? () + ? =
package and pc board thermal data VNL5160N3-E, vnl5160s5-e 18/26 doc id 16364 rev 2 5.2 so-8 thermal data figure 14. so-8 pc board note: layout condition of r th and z th measurements (pcb fr4 area = 58 mm x 58 mm,pcb thickness = 2 mm, cu thickness=35 m, copper areas: from minimum pad layout to 2 cm 2 ). r5 (c/w) 0.1 r6 (c/w) 115 45 c1 (ws/c) 0.0003 c2 (ws/c) 0.002 c3 (ws/c) 0.03 c4 (ws/c) 0.16 c5 (ws/c) 1000 c6 (ws/c) 0.4 2 table 16. sot-223 thermal parameter (continued) area/island (cm 2 )fp2 gapgcft005 3 4
VNL5160N3-E, vnl5160s5-e package and pc board thermal data doc id 16364 rev 2 19/26 figure 15. so-8 r thj-amb vs pcb copper area in open box free air condition figure 16. so-8 thermal impeda nce junction ambient single pulse equation 2: pulse calculation formula where = t p /t rthj_amb(c/w) rthjamb 65 75 85 95 105 115 0 0.5 1 1.5 2 2.5 pcb cu heatsink area (cm^2) - (refer to pcb layout) footprint 0.1 1 10 100 1000 0.0001 0.001 0.01 0.1 1 10 100 1000 time (s) zth (c/w) footprint 2 cm 2 z th r th z thtp 1 ? () + ? =
package and pc board thermal data VNL5160N3-E, vnl5160s5-e 20/26 doc id 16364 rev 2 figure 17. so-8 th ermal fitting mode (1) l 1. the fitting model is a simplified thermal tool and is valid for trans ient evolutions where the embedded protections (power limitation or thermal cycling during ther mal shutdown) are not triggered. table 17. so-8 thermal parameter area/island (cm 2 )0.072 r1 (c/w) 1.4 r2 (c/w) 3.2 r3 (c/w) 3.5 r4 (c/w) 21 r5 (c/w) 16 r6 (c/w) 58 28 c1 (ws/c) 0.0008 c2 (ws/c) 0.0032 c3 (ws/c) 0.0075 c4 (ws/c) 0.045 c5 (ws/c) 0.35 c6 (ws/c) 1.05 2
VNL5160N3-E, vnl5160s5-e package and packing information doc id 16364 rev 2 21/26 6 package and packing information 6.1 ecopack ? packages in order to meet environmental requirements, st offers these devices in different grades of ecopack ? packages, depending on their level of environmental compliance. ecopack ? specifications, grade definitions and product status are available at: www.st.com . ecopack ? is an st trademark. 6.2 sot-223 mechanical data figure 18. sot-223 mechanical data & package outline 0046067
package and packing information VNL5160N3-E, vnl5160s5-e 22/26 doc id 16364 rev 2 6.3 so8 mechanical data figure 19. so8 mechanical data & package outline outline and mechanical data dim. mm inch min. typ. max. min. typ. max. a 1.750 0.0689 a1 0.100 0.250 0.0039 0.0098 a2 1.250 0.0492 b 0.280 0.480 0.0110 0.0189 c 0.170 0.230 0.0067 0.0091 d (1) 4.800 4.900 5.000 0.1890 0.1929 0.1969 e 5.800 6.000 6.200 0.2283 0.2362 0.2441 e1 (2) 3.800 3.900 4.000 0.1496 0.1535 0.1575 e 1.270 0.0500 h 0.250 0.500 0.0098 0.0197 l 0.400 1.270 0.0157 0.0500 l1 1.040 0.0409 k0?8?0?8? ccc 0.100 0.0039 notes: 1. dimensions d does not include mold flash, protrusions or gate burrs. mold flash, potrusions or gate burrs shall not exceed 0.15mm in total (both side). 2. dimension ?e1? does not include interlead flash or protrusions. interlead flash or protrusions shall not exceed 0.25mm per side. so-8 0016023 d
VNL5160N3-E, vnl5160s5-e package and packing information doc id 16364 rev 2 23/26 6.4 sot-223 packing information the devices can be packed in tube or tape and reel shipments (see the table 1: device summary ). figure 20. sot-223 tape and reel shipment (suffix ?tr?) reel dimensions base q.ty 1000 bulk q.ty 1000 a (max) 330 b (min) 1.5 c ( 0.2) 13 f 20.2 g (+ 2 / -0) 12.4 n (min) 60 t (max) 18.4 tape dimensions according to electronic industries association (eia) standard 481 rev. a, feb. 1986 all dimensions are in mm. tape width w 12 tape hole spacing p0 ( 0.1) 4 component spacing p 8 hole diameter d (+ 0.1/-0) 1.5 hole diameter d1 (min) 1.5 hole position f ( 0.05) 5.5 compartment depth k (max) 4.5 hole spacing p1 ( 0.1) 2 top cover tape end start no components no components components 500mm min 500mm min empty components pockets saled with cover tape. user direction of feed
package and packing information VNL5160N3-E, vnl5160s5-e 24/26 doc id 16364 rev 2 6.5 so8 packing information figure 21. so-8 tube shipment (no suffix) figure 22. so-8 tape and reel shipment (suffix ?tr?) all dimensions are in mm. base q.ty 100 bulk q.ty 2000 tube length ( 0.5) 532 a 3.2 b 6 c ( 0.1) 0.6 c b a tape dimensions according to electronic industries association (eia) standard 481 rev. a, feb. 1986 all dimensions are in mm. tape width w 12 tape hole spacing p0 ( 0.1) 4 component spacing p 8 hole diameter d (+ 0.1/-0) 1.5 hole diameter d1 (min) 1.5 hole position f ( 0.05) 5.5 compartment depth k (max) 4.5 hole spacing p1 ( 0.1) 2 top cover tape end start no components no components components 500mm min 500mm min empty components pockets saled with cover tape. user direction of feed reel dimensions all dimensions are in mm. base q.ty 2500 bulk q.ty 2500 a (max) 330 b (min) 1.5 c ( 0.2) 13 f 20.2 g (+ 2 / -0) 12.4 n (min) 60 t (max) 18.4
VNL5160N3-E, vnl5160s5-e revision history doc id 16364 rev 2 25/26 7 revision history table 18. document revision history date revision changes 17-nov-2009 1 initial release. 20-feb-2012 2 update the entire document in st template. update section : features in cover page.
VNL5160N3-E, vnl5160s5-e 26/26 doc id 16364 rev 2 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a parti cular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. unless expressly approved in writing by two authorized st representatives, st products are not recommended, authorized or warranted for use in military , air craft, space, life saving, or life sustaining applications, nor in products or systems where failure or malfunction may result in personal injury, death, or severe property or environmental damage. st products which are not specified as "automotive grade" may only be used in automotive applications at user?s own risk. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or registered trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2012 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - philippines - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com

▲Up To Search▲

Price & Availability of VNL5160N3-E

	To Download VNL5160N3-E Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .